Product

Technical Parameters

Technical parameter	Parameter value
Brand	SONBEST
PH range	4~14
PH accuracy	±0.5
Applicable temperature range	0 to 65 ° C
Communication Interface	RS485
Default baud rate	9600 8 n 1
Power	DC6~24V 1A
Running temperature	-30~85℃
Working humidity	5%RH~90%RH

Product Size

Wiring instructions

Why choose this product?

Why choose this product?

How to use?

Application solution

Product List

Pictures

Precautions

1、电极在测量前必须用已知PH值的标准缓冲溶液进行定为校准，为取得更正确的结果，已知PH值要可靠，而且其PH值愈接近被测值愈好。
2、取下电极保护套后要注意，在塑料保护栅内的敏感玻璃泡不与硬物接触，任何破损和擦毛都会使电极失效。
3、测量完毕，不用时应将电极保护套套上，保护套内应放少量3.3mol/L氯化钾溶液，以保持电极球泡的湿润。
    4、电极的引出端，必须保持清洁和干燥，绝对防止输出两端短路，否则将导致测量结果失准或失效。
    5、电极避免长期浸在蒸馏水中货蛋白质溶液和酸性氟化物溶液中，并防止和有机硅油脂接触。
6、电极经长期使用后，如发现梯度略有极爱内地，则可把电极下端浸泡在4%HF（氢氟酸）中3-5秒钟，用蒸馏水洗净，然后在氯化钾溶液中浸泡，使之复新。
7、被测溶液中如含有易污染敏感球泡货堵塞液接界的物质，而使电极钝化，其现象是敏感梯度降低，货读数不准。如此，则应根据污染物质的性质，以适当溶液清洗，使之复新。
8、凡需测量能溶解聚碳酸树脂的有机溶剂，请选用PH符合电极中玻璃外壳型号电极。
    注：选用清洗剂时，如能溶解聚碳酸树脂的清洗液，如四氯化碳，三氯乙烯，四氢呋喃等，则可能把聚碳酸树脂溶解后，涂在敏感玻璃球泡上，而使电极失效，请慎用！

Communication Protocol

    The product uses RS485 MODBUS-RTU standard protocol format, all operation or reply commands are hexadecimal data. The default device address is 1 when the device leaves the factory, and the module or NON-Recorder default baud rate is 9600,8,n,1 ,but data recorder default baud rate is 115200 .
1. Read data (function code 0x03)
    Inquiry frame (hexadecimal), sending example: query 1 data of 1# device, the upper computer sends the command: 01 03 00 00 00 01 84 0A .

Address	Function Code	Start Address	Data Length	Check Code
01	03	00 00	00 01	84 0A

    For the correct query frame, the device will respond with data: 01 03 02 00 79 79 A6 , response format:

Address	Function Code	Length	Data 1	Check Code
01	03	02	00 79	79 A6

    Data description: The data in the command is hexadecimal, take data 1 as an example, 00 79 is converted to decimal value as 121, assuming the data magnification is 100, then the real value is 121/100=1.21, Others and so on.
2. Common data address table

Configuration Address	Register Address	Register Description	Data Type	Value Range
40001	00 00	pH	Read Only	0~65535
40101	00 64	Model Code	Read/Write	0~65535
40102	00 65	total number of measuring points	read/write	1~20
40103	00 66	device address	read/write	1~249
40104	00 67	baud rate	read/write	0~6
40105	00 68	communication mode	read/write	1~4
40106	00 69	protocol type	read/write	1~10